Autopage MA-200 Manuel d'installation télécharger pdf (Page 18)

5 +

H6/15 Gray Wire

Channel 3

Output =

Pulsed output

H6/15 Gray Wire

Channel 3

Output =

Latched output

H6/15 Gray Wire

Channel 3

Output =

Latched output

and reset with

ignition “on”

H6/15 Gray Wire

Channel 3 Output

= Timer

programming (set

to any interval

between 1 second

and 2 minutes.)

6 +

H6/7 Black /

Green Wire

Channel 4

Output =

Momentary

output

H6/7 Black /

Green Wire

Channel 4

Output =

Latched output

H6/7 Black /

Green Wire

Channel 4

Output =

Latched output

and reset with

ignition “on”

H6/7

Black / Green

Wire Channel 4

Output = Timer

programming (set

to any interval

between 1 second

and 2 minutes.)

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.

Channel 4 Timer Control Output Programming.

Enter:

1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2. Push the Valet switch 7 times (holding in on the 7th push) until three chirps with one long chirp is heard then release the

valet switch. You are now in the Alarm feature ‘C’ programming mode.

Timer Program:

1. Press and release and buttons together 4 times, [4] LED flash, [4] siren/horn chirps to indicate that you are in features

“Channel 4 Timer Programming mode”.

2. Press and hold the valet switch, the timer will immediately start.

3. When the desired interval has passed, release the valet switch. 1 long chirp for confirmation. (Set to any interval between 1

second and 2 minutes)

Note 1:

If your built-in timer controls window/sunroof closure in your car DO NOT change the timer setting! This requires installer-only

programming. Changing the value will adversely effect operation and may cause damage.

Note 2:

Momentary output = The momentary output selection will send a negative signal from the Channel 4 output immediately when the channel 4

button is pressed and will continue until the button is released.

Latched output = The latched output selection will send a negative signal as soon as the Channel 4 button is pressed and will continue until

the button is pressed again.

Latched output / reset with ignition = The latched / reset with ignition output selection operates just like the latched output but will reset or

stop when the ignition is turned on.

Password Pin Code Setup:

Enter:

1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.

2. Push the Valet switch 7 times (holding in on the 7th push) until three chirps with one long chirp is heard then release the

valet switch. You are now in the Alarm feature “C” programming mode. You can program or delete the password pin code as

below:

Program:

1. Press and release the transmitter button twice, [2] LED flash, [2] siren/horn chirp to indicate that you are in features

“Password Pin Code Programming mode”.

2. Within 5 seconds, begin to enter your chosen first 9ths digit by pressing and releasing the valet Switch from 1 – 9 times.

3. Within 15 seconds of the last entered 9ths digit, turn the Ignition switch to “ON” position.

4. Within 15 seconds, enter your chosen second 9ths digit by pressing and releasing the valet Switch from 1 – 9 times.

5. Finish by turning the ignition switch to “OFF” position.

If the new password code was accepted, the unit would report back the newly entered code, by flashing the LED, first indicating

the first digit code has been memorized, pause and then the second digit code. The unit will report the new code three times

with a one-second’s pause between each code.

Note: If 15 seconds of inactivity expire, or if the ignition switch is turned “ON” for more then 5 seconds during of above steps, the

unit will revert back to the last successfully stored code. Three long chirps will confirm exit. The unit will revert back to the last

successfully stored code

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 28 29

Commentaires sur ces manuels

Pas de commentaire

Autopage MA-200 Manuel d'installation Page 18

Commentaires sur ces manuels