1 C3-RS-730 LCD “ Multi-Color “ PROFESSIONAL 2-WAY LCD REMOTE CAR STARTER & ALARM SYSTEM With Built-in Temperature, Voltage Sensor And Two
10See Alarm Feature C – 6 Programming) Channel 4 Output (Factory default setting , Momentary grounded) This wire is built-in user-programmable ti
11(See Start Feature D - 1 Programming) In diesel vehicles it is necessary to interface with the wire that on the WAIT-TO-START light in the dashboar
121. Measure the resistance of the resistor pellet on the ignition key then select a resistor within 5% of the key’s value. 2. Locate the pair of V
13vehicle brake light circuit switches ground to the brake lights. An isolation diode must be used for ground switched brake light circuits and must
14VACUUM OPERATED CENTRAL LOCKING Green Wire Blue Wire +12V X Cut Compressor Door Switch 30 86 87a 85 87 30 86 87a85 87 3 Pin Plug To Alarm VACUUM
15FEATURES PROGRAMMING: ALARM FEATURE “A” PROGRAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the V
16 With Dome light turns on after ignition off: Some vehicles turn on the dome light when ignition key is turned off. After remote start, with alarm
17engine running) The shock sensor will be by-passed upon engine running. (The engine will run by itself after the ignition is turned off) The s
185 + H6/15 Gray Wire Channel 3 Output = Pulsed output H6/15 Gray Wire Channel 3 Output = Latched output H6/15 Gray Wire Channel 3 Output = Latc
19Delete Password Pin Code / Override without Password Pin Code (Factory default setting): Within 15 seconds, press and hold the transmitter butt
2HJKL TABLE OF CONTENTS: INSTALLATION DIAGRAMS 4 H1: 6 PIN HEAVY GAUGE WIRING CONNECTION 6 H1/1 Violet Wire – Starter Output 6 H1/2 &
203 Constant parking light output upon Remote Start Flashing parking light output upon Remote Start 4 20 minutes run time 30 minutes run time
214 Low check level Hi check level 5 Start or Stop the system for TESTING & ADJUSTMENT 6 + “TEST” Mode for Zone 2 / instant trigger
22VOLTAGE CHECKING TYPE 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 11 times and hold it
23c. Repeat the step1 – 4. 4. If the crank time is too short, (Engine not running, crank stopped before starting): a. Press the button once on the
24 TROUBLE SHOOTING There are 5 reasons why the remote start button will not respond from the transmitter. 1. The Black/White Neutral Safety wir
25b.If the starter engages, immediately step on the brake pedal to shut down the system, recheck your VIOLET wire (H1/1 starter output wire) connecti
26 METHOD 1 + 12 V Ignition Key In Sensor Switch Closes with Key In Ignition Cylinder Switch Drivers Door Pin Switch 87a 86 30 87 85 Key In Chime
27 Available At an Authorized Autopage Dealer The RS-730 is CI3 Compatible It is recommended to have a minimal digital service plan on your cell p
29 960 Knox Street Unit B Torrance, California 90502 Main Office: 310-323-1800 Technical Support: 800-945-2527 (For Authorized
3 INTRODUCTION This Remote Starter with Alarm and Keyless Entry System has been designed to be installed on fuel-injected vehicles with an au
4 INSTALLATION DIAGRAM Red : +12v inputViolet : Starter OutputYellow : Ignition 1 OutputPink : Ignition 2 OutputBrown : ACC/Heater OutputLED
520A20ARed: Remote Start Power 1Red: Remote Start Power 2Violet: Starter (+) OutputPink: Ignition 2 (+) OutputYellow: Ignition 1 (+) OutputBrown: Ac
6 WIRING Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Be sure to tape wires that pass through holes on the fi
7 Brown Wire –Accessory Output (Heater /AC Output) Connect the BROWN wire to the accessory wire in the vehicle that powers the climate control sys
8 H8. 2 PIN BLUE CONNECTOR FOR THE VALET SWITCH: (Under door on main unit) Select a mounting location for the switch that is easily accessible to t
9 H6 /1 BROWN/BLACK WIRE: 200 mA (-) Ground Output When Running. This wire provides a negative output during the remote start process. It ca
Commentaires sur ces manuels