7/9/2008
RS-603 REV A.
A. PROGRAMMING TRANSMITTER:
Note: This remote start system will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
PROGRAMMING THE REMOTE TRANSMITTER
1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in the ‘ON’ position. Within 15 seconds.
2. Push the Programming switch 2 times holding in on the 2
nd
push, until a long chirp from the horn (optional) and the LED
starts to flash then release the valet switch. You are now in the Transmitter programming mode.
3. Press the ‘Lock’ button on the transmitter until a chirp from the horn / a flash from the parking light / the LED turns on
for 2 seconds to confirming the first transmitter is now programmed.
4. Apply the same procedure (step 3) to program 2
nd
, 3rd and 4th
.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
FEATURE PROGRAMM
FEATURE “I” PROGRAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 1 times (holding in on the 1
st
push) until one chirp with one long chirp is heard, then
release the valet switch. You are now in the Alarm feature “A” programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
Three Chirps/
LED three pulse
1.
H3/2 White/Blue = 1 Pulse Remote
Start
H3/2 White/Blue = 3 Pulse
Remote Start
2.
H3/8 Pink Wire = Factory Security
Disarm Signal Output
H3/8 Pink Wire = Start Status
(Shock Sensor Bypass Control)
Output
H3/8 Pink Wire = 20
Second Ground out Key
Sensor By-pass
3. +
H2/4 Brown Wire = Horn Output
H2/4 Brown Wire = Rearm
Signal Output
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
FEATURE “II” PROGRAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 2 times (holding in on the 2
nd
push ) until two chirps with one long chirp is heard, then
release the valet switch. You are now in the Alarm feature “A” programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1.
Button Two Push
Remote
Button One push
Remote Start
2.
Without ignition
controlled door locks &
unlocks
Ignition controlled door
locks & unlocks
3. +
Gasoline Engine
Diesel Engine and 10
seconds warn-up timer
Diesel Engine and
15 seconds
warn-up timer
Diesel Engine and 20
seconds warn-up timer
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
(21 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels